您好!欢迎来到我们的网站
镇江百灵船舶用品有限公司
24小时服务热线:
20年生产循环水处理
0511-85728888
为广大用户提供优质的产品和完善的服务
Zhenjiang Bailing Ship Supplies Co., Ltd.
产品中心
地址:镇江市民营开发区
公司网址:WWW.ZJBLCB.COM
联系电话:0511-85728888
公司传真:0511-85728028
邮编:212111
联系我们
你的当前位置为:
919型消油剂(溢油分散剂)
    发布时间: 2019-08-05 09:32    
919型消油剂(溢油分散剂)


使用说明

919型消油剂(溢油分散剂)是处理消散流油品,处理环境污染的化学剂,配制方法独特,注重于解除制品毒性和强化渗透,扩散能力以及对油品的乳化消散功能、脱油效应,并可防止溢油火灾。
特点
1、处理的乳化能力强大,稳定性高,可生物降解性好;
2、属于”无毒类”产品,有利于保护水产资源;
范围
1、处理海洋、港口、江湖河流等水面上的溢流石油污染。
2、对炼油厂冷却水和其它排放含油污水浮油的处理。
3、用于油田排放水浮油的消散处理。
4、用于港口岸壁、船坞、栈桥、船甲板、滩涂、内燃机等各种机械设备外体和油舱、油罐、油管内外壁的脱油清洗,尤其是小管径油管的疏通。
5、用以控制溢油事故的发生。
方法
1、处理水面溢油污染时,用喷洒器具尽量均匀的将本剂洒向浮油(液粒不宜过分雾化),停留15—40分钟后,再经人工或机械(可用船艇航行)进行搅动,使本剂与溢油充分接触、渗透和吸收,即可达到理想的处理效果。
2、清洗机械等外体表面的聚积油时,喷洒本剂后,用工具刷动,再用净水冲洗。
3、用于油舱、油罐、油管内壁脱油时,使用压力泵冲射,然后用水冲洗。当油层过厚,粘性较大时,选用适度的高压泵操作。可重复循环冲洗,直到失去效力时,再换新剂。
用量比例根据油的品种、厚度及风化程度而定。通常对于新兴出的稀薄渍层,用量约为溢油的15-30%左右,油层较厚时应采取吸、刮和其它方法尽量回收。余下1mm左右时再施以本剂。遇有特殊情况,可继续增加用量,但最多不能超过溢油的一倍以上。
注意事项
远离火源,避免长时间爆晒、高温烘烤和低温冷冻。
包装
20公升塑料桶
 


919 Leakage Oil Disperser
Usage
919 Leakage Oil Disperser is a chemical agent which can be used to handle flowing oil product and environmental pollution. The confection method is unique, and the product is emphasizing on the removal of poison property, infiltration strengthening.diffusion capability, emulsification
function of oil, dispersion effect of oil or grease, prevention of leakage oil fire.
Characteristics :
I . Strong emulsification, high stability, k good biological decomposability.
2. It belongs to Non-poison product, avail to protect aquatic product resources.
Applications
1. handle the leakage petroleum pollution on the surface of sea. port, river or lake.
2. Handle the floating oil of cooling water or other drain waste water in petroleum-refining factory.
3. Handle the floating oil of drain waste water in oil field.
4. clean the out-surfoce of mechanical equipments such as port bank wall. boatyard, trestle, deck of ship, beach, diesel. etc., and oil cabin, oil tank. oil pipeline especially for small
size oil pipe.
5. Control the happening of oil leakage accident.
Using method
1. Spray the product uniformly to the floating oil. After 15-40 min.. agitate by manual or machine to gain better effect.
2. To clean the accumulating oil of the machinery surface use brush after spraying the agent, then wash with clean water.
3. To clean the inner wall of oil cabinl. oil tank and oil pipe flush, with pressure Pump then wash with water. If the oil layer is too thick and the viscosity is too high flush with proper high pressure pump.
Dosage
The dosage is determined by the oil type. thickness or oil layer and airslake degree. For thin oil layer the dosage will be 15-30% of oil quantity. If the oil layer is too thick callback the
oil to the best of one's abilities until the layer is about 1 mm. If encountering special condition may continue adding the agent with the max. dosage less than one times of leakage
oil quantity.
Attention
Keep away from fire source. Avoid long time sunshine, also avoid to be baked at high temperature or frozen at low temperature.
Packing
Big size iron drum; 200 Liter
Irom drum: 20 Liter