903型强力除碳剂
说明
903除碳清洁剂是一种性质卓越渗透力强的溶剂。混合其他清洁剂和锈蚀抑制剂等而成。专用以清除柴油机内各种活塞、活塞环、阀及其他零件等，在燃烧后所聚集的积垢、炭素、油漆和黏性物质。
使用法
903除碳清洁剂，能渗透沉积污垢、溶解油料、油脂、油漆及燃烧不完全的物质。又能使不能溶解的矿物质(炭、烟灰、灰垢、污物)软化，以便揩擦清除。
903除碳清洁剂又可用作清洁零件及整件机械之用。例如用作清洗油低、乳胶及环氧漆等极为有效。
建议两种清洁方法：
A、浸洗法：
1、除去橡胶附件。将待清洁的零件放入大小适度的盘或桶内。以除碳清洁剂浸过其表面，小零件则放置于铁丝篮中，以便于去污及取出。
2，浸洗时间，必须等待所有沉积污垢完全溶解或松脱为止(通常为4至8小时)。但其所需正确时间，须视积垢之厚度和性质而定。
a．当沉积污垢过于严重时，需要不时搅动其溶剂。
b．当沉垢已碳化，则溶剂须加热至55℃—60℃(130˙F—140˙F)，不可加热至75℃(165˙F)以上。
3，从清洁盆内取出，用水冲洗，以清除尚留存在零件上的酥松污物，然后用布抹干或用压缩空气吹干。
B、擦洗法：
重大机械在原地清洗，可用沾有除碳清洁剂的漆刷擦刷污处(勿用橡皮毛刷)。擦刷时，漆刷须常蘸有溶液，直至清洁为止。在擦刷时，空气必须流通。清洁完
毕用湿布揩抹，再用干布抹干。
详细的清洁程序可依据利用的器具，而由工程师随意决定。
处理
在处理时，戴上护目镜及塑胶手套。空气流通，避免过久吸入蒸发气体。如若意外的接触皮肤，立即用水清洗。如液体意外的进入眼睛，即用水清洗，并送医。
包装
20KG/塑料桶
贮存
贮放处远离烟火。
ENGLISH
903 Powerful Carbon Removal Agent
903 carbon Removal Agent is a best and strong solvent with high leakage ability, which mix other detergent and corrodent. It is used specially to clean the dirt, carbon, paint and adhesive matters accumulated in the diesel.
Usage
903 Carbon Removal Agent can filtrate the dirt.solute the grease, oil. paint and the matter not completed fired. 903 Carbon Removal Agent has the purpose of cleaning machine parts and completed machinery, for example, it is effective in cleaning the grease, emulsified rubber and epoxy paint.
Here we suggest two methods.
A. baptism method
1. clean out the rubber enclosure, put the parts to be cleaned into the properly barrier, soak the surface with 903 Carbon Removal Agent.
2. soaking time, it must wait all the dirt and grease solute or loose(as usual for 4-8 hours).
a.when the dirt and grease is seriously dried, it needs shaking the solution now and then.
b.when the dirt and grease is carbonated, heat the solution Upto55C-60c(130˙F-40˙F)
Heating the agent to above 75℃ (165˙F) is forbidden.
3.take it out of the cleaning basin, and wash it so as to clean the dirt on the parts, then dry it with cloth or blow it with compressed air.
B detergent way
It is available to clean the heavy machinery at site. use the paint bruxh to brush the dirty parts. When brushing remember dipping the agent usually. After the cleaning, dry it with
cloth. Detailed cleaning procedure subjects to the site condition and can be determined be the engineer.
Attention
When handlingweor eye-protector and plastic gloves. Avoid breathing the agent longer time. Immediately wash with water if contact the agent. If necessary send to hospital for further
assistance.
Packing
903 Carbon Removal Agent is always packed into 25 Liter small drum
Storage
